Acquisition Software
Data Acquisition
The main function of Acq is to set collection parameters such as sample rate, collection duration, set patient information, set data filters, set synthetic gradiometer order, set adaptive balancing, set up triggers and ADCs, collect and save data, perform head localization to co-register the sensors to the head coordinate frame, save collection parameters for future use. Collection Parameters are set via dialog boxes prior to recording and stored in a protocol file. However, these parameters can be adjusted for a given study without permanently changing the stored protocol file and should always be reviewed before starting a collection.
Data can be collected in one of three modes:
- Continuous recording displays all data immediately while recording
- triggered recording stores individual or averaged sets of trials with specified time duration around some form of stimulus or external trigger
- Un-triggered recording stores trials of a specified duration in response to the operator’s command without stimulus triggering.
The final preparation before recording is the localization of the subject’s head with respect to the standard coordinate system. This is done by localizing the position of coils placed on the fudicial landmark points of the subject’s head via the SQUID sensors after the subject’s head is placed in the dewar helmet. You can then either use continuous head localization to track the position of the head throughout the scan, or repeat the position measurement at the end of the recording.
Running Acq
From the Acquisition Console / Workstation:
- Open the NIMH MEG Core Facility Acquisition Manager
- Select User
- Select study type
- Enter subject name (first name first) and MRN
- Launch Acq
3. To view/edit Collection Parameters: a. Click on Windows b. Click on Collection Parameters
4. Click OK.
5. At the Acq Dialog Window enter:
Acq Dialog Window
a. Enter Subject ID (subject initials & MIS#). b. Enter Procedure Description.
6. Click on Acquire Data.
7. Create Directory? Click Ok.
8. When performing EEG, an IMPEDANCE CHECK should be performed on the MEG system:
• Select EEG Setup Window menu. • Click on CHECK IMPEDANCE. The results are displayed in the appropriate columns. – To check the impedance of all active EEG channels press the CTRL key on the keyboard at the same time as clicking on the impedance check button. – Please note: The impedance check requires 3 electrodes: The electrode being measured and at least 2 other electrodes. • Click OK / EXIT.
9. Click on HEAD LOCALIZATION button located on the side bar.
10. Instruct subject for task and Head Localization. If applicable UNBLANK SCREEN.
11. At the Stimulus Workstation: Click the mouse to activate the “LOCALIZING HEAD” prompt. *If there is no head localization prompt, omit this step.
12. Click on OK at the Head Localization Starter TO START THE LOCALIZATION.
Head Localization Window
13. Click on CONTINUE to accept the head localization results. (acceptable tolerance is < 0.5 mm)
14. STARTING THE STIMULUS: a. If acquisition is NOT TRIGGERED click mouse on the Stimulus
Computer simultaneously with the start of the Data Collection (Step# 15),
b. If trial is TRIGGERED click mouse after the start of collection
(Step# 15).
15. To start DATA COLLECTION click on START.
Acquisition Monitor
16. To select the ADCs and Channels to be displayed during collection: Click on the CHANNEL SET BUTTON which is below the group of Channel Scale Indicators.
Note: Select Custom… to customize the channel selection using the Channel Selector dialog.
Note: Fluctuating Red lights in the Collection Status Window during acquisition indicates that the data is being buffered; a failure condition is indicated only if the collection status buffer in completely red (full).
Solid yellow lights on the DSQ cards during acquisition indicate those channels are actively acquiring data; not a failure condition.
17. Click on the CHANNEL SELECTOR DIALOG;
a. From the UNSELECTED Window click on the
channels (i.e., Stim, ADC’s, EOG, EEG and/or MEG channels) to be displayed.
b. Click on the ARROW to transfer those channels to the SELECTED window. *Make sure the ADCs have been set up correctly and document. c. Click on APPLY.
Channel Selector Dialog
18. Adjust channel (display) scale.
19. When done acquiring (at the end of the trial) when data collection stops, head localization will start automatically. Wait for the HEAD LOCALIZATION PROMPT. 20. To Print the Head Localization results: When Head Localization is done Click at the bottom of the screen and the Printer Icon will display. Click on the printer icon then click anywhere within the Head Localization dialog.
21. Click on “Continue” to accept the data. *If localization fails click on the REPEAT button to re-try localization. At the General Information window, click OK.
22. When head localization is done instruct the subject to relax and blank the screen.
23. To begin another trial :
a. Click on FILE.
b. Click on CLOSE WINDOW.
c. Acquisition Manager window displays.
d. Edit the trial information in the Procedure area.
e. Click on OK.
f. Repeat steps 5 - 22.
24. When done inform subject of study completion and blank the screen.
25. To end recording session click on CLOSE window.
26. EXIT Acq.
27. Select Dataset to save.
28. Click on OK.
29. From the Acquisition Manager window select the dataset to push to the storage RAID SERVER (tako.nimh.nih.gov).
30. Click on Push Data.
NIMH MEG Core Facility Acquisition Manager